POLYWATER LP-D5 Polywater Drill-Operated Lubricant Pump 02786800355 SOLD PER EACH
Available*
Item # 55460085
Model # LP-D5
$1,073.00
financing available. Learn More
* Notes on Availability:
If item is in stock, it will ship same day.
Lead times vary, contact us for more info.
(Images may not be of the actual item being sold.)
- Product Description
- You Might Also like
- Recently Viewed
Generic
Class
Group
Type
Manufacturer
LOT
Lubricants
Material and Supplies
Lubricants-Sealants
Lubricant- Greases
Polywater
Warning: This product can expose you to chemicals, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.govProduct Description
AMERICAN POLYWATER LP-D5 Polywater® Drill-Operated Lubricant Pump 02786800355 SOLD PER EACH
Model LP-D5 Cable Pulling Lubricant Pump for 5-Gal Pails & 55-Gal Drums
The new and improved Polywater® Lubricant Pump Model LP-D5 is a drill-operated, self-priming gear pump. All Polywater® lubricants can be pumped directly into the conduit or onto the cable during cable installations at rates exceeding 1.5 gallons per minute.
The LP-D5 pump sets directly onto a 5-gallon pail or 55-gallon drum and comes with a 10-foot discharge hose. Click here to see the LP-D5 in field use on a large power utility cable installation project.
The LP-D5 pump now includes two hands-free applicators (shown at right) for 1.5-inch to 6-inch conduits. Polywater® Cable Pulling Lubricant Pump Model LP-D5 now includes two hands-free applicators for 1.5-inch to 6-inch conduits.
ADVANTAGES
Practical Transfer of all Polywater® Lubricants -- Save time and effort in cable pulling. Eliminate hand scooping, messy pouring, and lengthy clean-ups.
The LP-D5 pump sets directly onto a 5-gallon pail or 55-gallon drum and comes with a 10-foot discharge hose.
Variable Pumping Capability -- Adjustable speed ½-inch drill (not included) allows pump to deliver lubricants at a rate of 1.5 gallons per minute, or higher.
Consistent Lubricant Application -- Automates lubricant application with constant lubrication throughout installation.
Convenient -- No hand pumping. Requires battery or electric variable speed ½-inch drill.
Easy Maintenance -- Minimum assembly required. Cleans up with water.
Corrosion Resistant -- A solid brass body and stainless steel shaft.
OPERATION
Open pail or drum. With drum, untie and open liner, then replace drum cover. Set LP-D5 pump in 5-gallon pail or into the 2-inch bung hole of a 55-gallon drum. Attach variable speed drill to LP-D5. Insert free end of hose into conduit opening, pail or jug. Set drill to OPERATE IN FORWARD. Start drill to pump lubricant until it is visible at hose end. If installing cable, start pulling cable and start variable speed ½-inch drill to pump lubricant at desired flow rate.
CLEANING
Pump clean tap water through LP-D5 pump until water discharge is clear and no lubricant is apparent. Let pump containing tap water soak for 15 minutes. Run pump again with clean tap water to remove any remaining lubricant. Repeat the process as necessary. Wipe off pump. Protect from dirt with bag or other cover.
Keep dirt and debris away from pump to avoid damage. Avoid running pump dry to prevent damage.
Model LP-D5 Cable Pulling Lubricant Pump for 5-Gal Pails & 55-Gal Drums
The new and improved Polywater® Lubricant Pump Model LP-D5 is a drill-operated, self-priming gear pump. All Polywater® lubricants can be pumped directly into the conduit or onto the cable during cable installations at rates exceeding 1.5 gallons per minute.
The LP-D5 pump sets directly onto a 5-gallon pail or 55-gallon drum and comes with a 10-foot discharge hose. Click here to see the LP-D5 in field use on a large power utility cable installation project.
The LP-D5 pump now includes two hands-free applicators (shown at right) for 1.5-inch to 6-inch conduits. Polywater® Cable Pulling Lubricant Pump Model LP-D5 now includes two hands-free applicators for 1.5-inch to 6-inch conduits.
ADVANTAGES
Practical Transfer of all Polywater® Lubricants -- Save time and effort in cable pulling. Eliminate hand scooping, messy pouring, and lengthy clean-ups.
The LP-D5 pump sets directly onto a 5-gallon pail or 55-gallon drum and comes with a 10-foot discharge hose.
Variable Pumping Capability -- Adjustable speed ½-inch drill (not included) allows pump to deliver lubricants at a rate of 1.5 gallons per minute, or higher.
Consistent Lubricant Application -- Automates lubricant application with constant lubrication throughout installation.
Convenient -- No hand pumping. Requires battery or electric variable speed ½-inch drill.
Easy Maintenance -- Minimum assembly required. Cleans up with water.
Corrosion Resistant -- A solid brass body and stainless steel shaft.
OPERATION
Open pail or drum. With drum, untie and open liner, then replace drum cover. Set LP-D5 pump in 5-gallon pail or into the 2-inch bung hole of a 55-gallon drum. Attach variable speed drill to LP-D5. Insert free end of hose into conduit opening, pail or jug. Set drill to OPERATE IN FORWARD. Start drill to pump lubricant until it is visible at hose end. If installing cable, start pulling cable and start variable speed ½-inch drill to pump lubricant at desired flow rate.
CLEANING
Pump clean tap water through LP-D5 pump until water discharge is clear and no lubricant is apparent. Let pump containing tap water soak for 15 minutes. Run pump again with clean tap water to remove any remaining lubricant. Repeat the process as necessary. Wipe off pump. Protect from dirt with bag or other cover.
Keep dirt and debris away from pump to avoid damage. Avoid running pump dry to prevent damage.
