TYCO 804059-000 HEAT SHRINKABLE CABLE END CAPS WITH AIR VALVE RANGE 1.7-3.5 INCHES **MOQ 25**
Available*
Item # 57656100
Model # 804059-000
$13.61
financing available. Learn More
* Notes on Availability:
If item is in stock, it will ship same day.
Lead times vary, contact us for more info.
(Images may not be of the actual item being sold.)
- Product Description
- You Might Also like
- Recently Viewed
Generic
Class
Group
Type
Manufacturer
LOT
Air
Material and Supplies
Air Pressure
Parts- Miscellaneous
RUS Industries Inc
Warning: This product can expose you to chemicals, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.govProduct Description
RUS INDUSTRIES TYCO 804059-000 HEAT SHRINKABLE CABLE END CAPS WITH AIR VALVE RANGE 1.7-3.5 INCHES **MOQ 25** MINIMUM ORDER 25
VAAC and FAAC self-adhering, heat-shrinkable cable end caps seal water out and seal pressure in on polyethylene jacketed cable, pipes and conduits. Systems approved, these highly reliable end caps are available with or without valves. They are used extensively by major telephone companies and telephone cable manufacturers. Reliability through rugged design A special design and a tough new compound make VAAC and FAAC end caps highly resistant to impact, even at very low temperatures. Cable pressure is maintained throughout thermal cycles from -40¢ªF to 140¢ªF and thermal shock tests to -100¢ªF. Convenience The expansion ratios enable just four sizes of end caps to cover cables from 0.4 inches to 3.5 inches in diameter. Inventories are reduced, and ordering is simplified. One step sealing When fully recovered, VAAC and FAAC end caps bond directly to the cable jacket. Separate application of sealant, tapes, or hose clamps is eliminated. Easy installation and removal VAAC and FAAC end caps are quickly installed by one person. No special training is required. The operator simply wipes loose dirt from the cable and heats the cap until it has shrunk over the cable end. When using an approved torch to recover the cap, the operator must protect the cable sheath by using a three-inch wrap of aluminum tape adjacent to the cable. To remove the assembly, the operator just makes slits in the cap at one-and-a-half-inch intervals and pulls it off the cable. Pressure rating VAAC and FAAC end caps seal 12 psig continuously under typical use and environmental conditions. The product is unaffected by flash testing at 25 psig.
Product Description/Part number Minimum Cable Range Flat end FAAC-100/804054 .4-.8 (10 - 20) FAAC-200/804055 .8 - 1.7 (20 - 43) FAAC-250/118491 1.6 - 2.5 (41 - 64) FAAC-300/804056 1.7 - 3.5 (43 - 89) Valved end VAAC-100/804057 .4 - .8 (10 - 20) VAAC-200/804058 .8 - 1.7 (20 - 43) VAAC-250/527722 1.6 - 2.5 (41 - 64) VAAC-300/804059 1.7 - 3.5 (43 - 89)
***must be ordered in quantities of 25***
VAAC and FAAC self-adhering, heat-shrinkable cable end caps seal water out and seal pressure in on polyethylene jacketed cable, pipes and conduits. Systems approved, these highly reliable end caps are available with or without valves. They are used extensively by major telephone companies and telephone cable manufacturers. Reliability through rugged design A special design and a tough new compound make VAAC and FAAC end caps highly resistant to impact, even at very low temperatures. Cable pressure is maintained throughout thermal cycles from -40¢ªF to 140¢ªF and thermal shock tests to -100¢ªF. Convenience The expansion ratios enable just four sizes of end caps to cover cables from 0.4 inches to 3.5 inches in diameter. Inventories are reduced, and ordering is simplified. One step sealing When fully recovered, VAAC and FAAC end caps bond directly to the cable jacket. Separate application of sealant, tapes, or hose clamps is eliminated. Easy installation and removal VAAC and FAAC end caps are quickly installed by one person. No special training is required. The operator simply wipes loose dirt from the cable and heats the cap until it has shrunk over the cable end. When using an approved torch to recover the cap, the operator must protect the cable sheath by using a three-inch wrap of aluminum tape adjacent to the cable. To remove the assembly, the operator just makes slits in the cap at one-and-a-half-inch intervals and pulls it off the cable. Pressure rating VAAC and FAAC end caps seal 12 psig continuously under typical use and environmental conditions. The product is unaffected by flash testing at 25 psig.
Product Description/Part number Minimum Cable Range Flat end FAAC-100/804054 .4-.8 (10 - 20) FAAC-200/804055 .8 - 1.7 (20 - 43) FAAC-250/118491 1.6 - 2.5 (41 - 64) FAAC-300/804056 1.7 - 3.5 (43 - 89) Valved end VAAC-100/804057 .4 - .8 (10 - 20) VAAC-200/804058 .8 - 1.7 (20 - 43) VAAC-250/527722 1.6 - 2.5 (41 - 64) VAAC-300/804059 1.7 - 3.5 (43 - 89)
***must be ordered in quantities of 25***
