POLYWATER AR-KIT97 AirRepair Sealant Kit with Putty 02786805030 SOLD PER Case
Available*
Item # 55461200
Model # AR-KIT97
$116.10
financing available. Learn More
* Notes on Availability:
If item is in stock, it will ship same day.
Lead times vary, contact us for more info.
(Images may not be of the actual item being sold.)
- Product Description
- You Might Also like
- Recently Viewed
Generic
Class
Group
Type
Manufacturer
LOT
Lubricants
Material and Supplies
Lubricants-Sealants
Adhesive
Polywater
Warning: This product can expose you to chemicals, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.govProduct Description
AMERICAN POLYWATER AR-KIT97 AirRepair® Sealant Kit with Putty 02786805030 SOLD PER Case AMERICAN AMERICAN POLYWATER AR-KIT97 AirRepair® Sealant Kit with Putty 02786805030 SOLD PER Case
Eliminate Hot Lead Wiping!
AirRepair® -- A Revolutionary Leak Repair System for Pressurized Telephone Cable Systems. Stops Air Escaping from Lead Sheathed Splice Enclosures and Polyethylene Components. Eliminates Hot Wipe Procedures.
Pressurized Leak Repair System
FEATURES
MULTIPLE USES - Seals air leaks in lead-sheathed cables and splice enclosures, polyethylene stalpeth cable jackets, load coils, end-plates, and more. Click here for Application Photos. EASY TO APPLY - Paste seals hard-to-reach areas. FAST CURE - Typically ready for pressurization in under 15 minutes. SAVES MONEY - Less expensive and faster than hot lead wiping. SIMPLE - No torches, or power sources; no wrapping or clamping required. CONVENIENT - Kit contains all materials needed to seal multiple leaks. DURABLE - Impervious to water and many other manhole contaminants.
AirRepair® is a revolutionary new leak repair system for pressurized telephone cables and splices. AirRepair® seals air leaks in lead-sheathed cables and splice enclosures, polyethylene stalpeth cable jackets, load coils, end-plates, and more. AirRepair® eliminates messy and dangerous molten lead hot wipe procedures. AirRepair® allows a single craftsperson, with minimal training, to effectively and economically seal 20 or more leaks per day.
AirRepair® Sealant is a 2-part, fast curing, gray paste. The AirRepair® 2-part paste is packed in an easy-to-use system. Pre-measured packaging contains enough material to seal one typical leak, approximately 6 square inches at a coating thickness of 1/4 inch.
AirRepair® is a no-sag paste that, once mixed, can be immediately applied to the cable or splice underside, along seams, and in the crotch area. The sealant will hold air pressure within 10 minutes of mixing and application. The sealant cures at ambient temperatures as low as 40°F, forming a tough seal. The cured seal is resistant to water, salt, oils, and other manhole contaminants.
PHYSICAL PROPERTIES Color: Dark Grey Cured Hardness: 75 (Shore D) Viscosity: No-Sag, Thick Paste Durability: Resistant to Water Pot Life: 5 Minutes @ 70°F/21°C Adhesion to Lead & Metals: Good Adhesion to Plastic: Good (may require primer)
Eliminate Hot Lead Wiping!
AirRepair® -- A Revolutionary Leak Repair System for Pressurized Telephone Cable Systems. Stops Air Escaping from Lead Sheathed Splice Enclosures and Polyethylene Components. Eliminates Hot Wipe Procedures.
Pressurized Leak Repair System
FEATURES
MULTIPLE USES - Seals air leaks in lead-sheathed cables and splice enclosures, polyethylene stalpeth cable jackets, load coils, end-plates, and more. Click here for Application Photos. EASY TO APPLY - Paste seals hard-to-reach areas. FAST CURE - Typically ready for pressurization in under 15 minutes. SAVES MONEY - Less expensive and faster than hot lead wiping. SIMPLE - No torches, or power sources; no wrapping or clamping required. CONVENIENT - Kit contains all materials needed to seal multiple leaks. DURABLE - Impervious to water and many other manhole contaminants.
AirRepair® is a revolutionary new leak repair system for pressurized telephone cables and splices. AirRepair® seals air leaks in lead-sheathed cables and splice enclosures, polyethylene stalpeth cable jackets, load coils, end-plates, and more. AirRepair® eliminates messy and dangerous molten lead hot wipe procedures. AirRepair® allows a single craftsperson, with minimal training, to effectively and economically seal 20 or more leaks per day.
AirRepair® Sealant is a 2-part, fast curing, gray paste. The AirRepair® 2-part paste is packed in an easy-to-use system. Pre-measured packaging contains enough material to seal one typical leak, approximately 6 square inches at a coating thickness of 1/4 inch.
AirRepair® is a no-sag paste that, once mixed, can be immediately applied to the cable or splice underside, along seams, and in the crotch area. The sealant will hold air pressure within 10 minutes of mixing and application. The sealant cures at ambient temperatures as low as 40°F, forming a tough seal. The cured seal is resistant to water, salt, oils, and other manhole contaminants.
PHYSICAL PROPERTIES Color: Dark Grey Cured Hardness: 75 (Shore D) Viscosity: No-Sag, Thick Paste Durability: Resistant to Water Pot Life: 5 Minutes @ 70°F/21°C Adhesion to Lead & Metals: Good Adhesion to Plastic: Good (may require primer)
