POLYWATER TC-1D42 42 TC-1 in a Dispenser Pack 02786806693 SOLD PER Case
Available*
Item # 51848865
Model # TC-1D42
$89.22
financing available. Learn More
* Notes on Availability:
If item is in stock, it will ship same day.
Lead times vary, contact us for more info.
(Images may not be of the actual item being sold.)
- Product Description
- You Might Also like
- Recently Viewed
Generic
Class
Group
Type
Manufacturer
LOT
Wipes
Fiber Optic Products
Fusion and Mechanical Splicing
Cleaning supplies
Polywater
Fiber One Click - Cletop - Wands
Warning: This product can expose you to chemicals, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.govProduct Description
AMERICAN POLYWATER TC-1D42 42 TC-1 in a Dispenser Pack 02786806693 SOLD PER Case
Cleans off pik without the use of alcohol Minimal wiping (2 wipes only) No residue Safe to use on ribbon fiber Fans fiber quickly Cleans fiber squeaky clean Tested and approved
New SqueekyKleen™ cleans and fans fiber in two wipes without alcohol, saving time and money. Hear the difference! No follow-up with alcohol required to get fibers squeaky clean and separated when prepping for splicing. SqueekyKleen™ is less harsh on hands and reduces chemical odors and vapor concentrations to a minimum in splice trailers and vaults. SqueekyKleen's™ unique formulation and specially designed high-performance towelette work to remove pik from the entire surface of loose-tube or ribbon fibers, leaving no residue. SqueekyKleen™ helps keep splice equipment clean of contamination for better fiber alignment and splice quality. Safe on acrylate and Mylar®.
Specifications
Cleaning: When wiping a 3-foot section of 12-count fiber from a buffer tube, the pre-saturated towel will squeak and fan fibers with 2 wipes.
Solvency Power: At 68° F (20°C), will dissolve .020 (.5mm) film of PE/PJ or ETPR grease completely from cable jacket with less than two minutes of vigorous agitation (no wiping).
Residue: When placed on a clean glass panel and dried, the solvent shall not leave any visible residue (<100 ppm).
Water Content: When tested by the ASTM 1533B method, water content shall be less than 75 ppm.
Flash Point: When tested via a Pensky-Martin Closed Cup Test (ASTM D93), the cleaner shall have a flash point above 140°F.
Cleans off pik without the use of alcohol Minimal wiping (2 wipes only) No residue Safe to use on ribbon fiber Fans fiber quickly Cleans fiber squeaky clean Tested and approved
New SqueekyKleen™ cleans and fans fiber in two wipes without alcohol, saving time and money. Hear the difference! No follow-up with alcohol required to get fibers squeaky clean and separated when prepping for splicing. SqueekyKleen™ is less harsh on hands and reduces chemical odors and vapor concentrations to a minimum in splice trailers and vaults. SqueekyKleen's™ unique formulation and specially designed high-performance towelette work to remove pik from the entire surface of loose-tube or ribbon fibers, leaving no residue. SqueekyKleen™ helps keep splice equipment clean of contamination for better fiber alignment and splice quality. Safe on acrylate and Mylar®.
Specifications
Cleaning: When wiping a 3-foot section of 12-count fiber from a buffer tube, the pre-saturated towel will squeak and fan fibers with 2 wipes.
Solvency Power: At 68° F (20°C), will dissolve .020 (.5mm) film of PE/PJ or ETPR grease completely from cable jacket with less than two minutes of vigorous agitation (no wiping).
Residue: When placed on a clean glass panel and dried, the solvent shall not leave any visible residue (<100 ppm).
Water Content: When tested by the ASTM 1533B method, water content shall be less than 75 ppm.
Flash Point: When tested via a Pensky-Martin Closed Cup Test (ASTM D93), the cleaner shall have a flash point above 140°F.
